HKM-016787 16-Inch Bladeless Tower Fan with Remote Ten Speeds Timer Child-Safe Airflow for Bedroom and Nursery

HKM-016787 · Bladeless Tower Fan · () · 5 kg gross

16-Inch Bladeless Tower Fan with Remote and Child-Safe Airflow16-Inch Bladeless Tower Fan with Remote

A 39 in (100 cm) bladeless tower with a 16 in loop, ten fan speeds, 70 degree oscillation, a 1 to 8 hour timer and a remote that docks on the tower. There is no exposed blade at any height, so a toddler who reaches for the loop touches smooth plastic and moving air instead of a spinning guard.

The loop pulls air in through the base, accelerates it through a narrow slot and pushes it out as one continuous sheet. That is why the airflow arrives smooth rather than chopped, and why the tower can sit two feet from a crib without the buffeting a bladed fan gives you at that distance. The impeller that does the work sits inside the cylinder below, behind a grille a finger cannot reach through.

It suits a bedroom, a nursery or a living room corner where a bladed fan is a hazard or an eyesore. It is not an air conditioner: the tower moves air, it does not chill it, so a 95 F room stays 95 F and simply feels less still.

At a Glance

• 16 in Loop — 40.6 cm oval, 39 in / 100 cm floor standing
• No Exposed Blade — Smooth loop, safe around toddlers and pets
• 10 Fan Speeds — Plus sleep mode and a display that dims
• 70 Degree Oscillation — Wide sweep, switchable to fixed
• Remote + Panel — Both work, remote docks on the tower
• 1 to 8 Hour Timer — Set it and let the room settle
• 45W Brushless Motor — Runs on 120 V, costs cents a night
• 40 to 55 DB — Sleep mode is the quietest step
• 3.6 kg Net — 5 kg boxed, 50 x 25 x 20 cm carton
• 2 Finishes — Silver and Gold, both with a white body
• Wipe-clean Loop — No grille to unscrew, no blade to dust
• 120 V AC, 60 Hertz — US plug, 5 ft cord

What the Tower Is Made Of

The loop is a single piece of painted ABS with a matte outer face and a satin inner channel. The two halves are screwed together rather than clipped, which matters after a move: a clipped loop develops a rattle at speed six and there is no way to tighten it. The base is a 8.7 in (22 cm) cylinder weighted with a steel plate, so a 39 in tower does not walk across a wood floor when the oscillation is on.

The intake grille wraps the lower third of the cylinder and is molded in one piece with the housing, so there is no seam for dust to catch in. Behind it sits a mixed-flow impeller on a brushless DC motor. Brushless matters here for two reasons: the motor lasts longer than a brushed one at low speed, and it can hold a steady 600 rpm at step one instead of stalling and hunting, which is what makes a cheap tower hum in a bedroom.

The control cluster is on the top face of the base, angled up so you can read it standing over the tower. Four buttons cover power, speed, oscillation and timer, with a small blue LED ring that shows the setting. The remote mirrors those four functions and adds a sleep key that steps the fan down one speed every hour and dims the LED. The remote cradle is a magnet in the loop base, so the remote lives on the tower instead of in a drawer.

• Painted ABS loop, 16 in / 40.6 cm oval, matte outer face
• Weighted cylinder base, 8.7 in / 22 cm, non-marking feet
• Brushless DC motor, 45W, 600 to 1650 rpm
• Magnetic remote cradle on the loop base
• 5 ft cord with a US two-prong plug

Two details decide whether a bladeless tower feels cheap in the hand. The first is slot width: too wide and the airflow collapses into a lazy puff, too narrow and it whistles at high speed. This one runs a 1.5 mm slot around the full oval. The second is balance. The impeller is balanced with a correction weight before assembly, and the loop is isolated from the base with a rubber gasket, so the tower does not transmit a hum into a bedside table through its own feet.

How the Air Moves

A mixed-flow impeller inside the base pulls room air through the lower grille and pressurizes the loop. The air escapes through the 1.5 mm slot that runs around the inside of the oval, and because the slot is continuous the sheet leaves the loop at the same speed along its whole height. A bladed fan cannot do that: its airflow peaks at the blade tips and falls away between them, which is the chop you feel on your face.

The second effect is entrainment. The sheet leaving the slot drags still room air along with it, so the volume that reaches you is several times what the impeller actually moves. That is the honest explanation for why a 45W bladeless tower feels stronger than a 45W bladed fan of the same rating, and also why the number on the box is airflow in cubic feet per minute rather than a made-up multiplier.

At step one the tower moves about 210 CFM and at step ten about 480 CFM, measured at the loop face. For a 150 sq ft bedroom that is enough to turn the air over every four to six minutes at step four, which is where many people leave it overnight.

Oscillation sweeps 70 degrees on a geared ring in the base, not on the motor shaft. Putting the sweep downstream of the motor keeps the motor at a constant load, so the pitch of the fan does not change as the tower turns. It also means the sweep can be stopped at any point without the tower drifting.

Where It Works and Where It Does Not

It suits a room up to about 250 sq ft with the tower in a corner and the loop aimed across the space rather than at a sofa. Placed against a wall it will move air along the wall and feel weak; placed 12 to 18 in out from the corner it will fill the room. In a nursery the sleep mode plus the 2 hour timer is the setting many buyers end up using: the fan steps down as the room cools and the LED goes dark so it does not light the ceiling.

It is not a substitute for air conditioning, and it is not a purifier. There is no filter in this model. If you want filtration you need the version with the HEPA cartridge in the base, which is a different product. What this tower does is keep air moving at a speed you can sleep in, which is the actual reason people buy a fan.

• Nursery: sleep mode, timer 2 to 4 hours, oscillation on
• Bedroom: step three or four, fixed, pointed along the bed not at it
• Living room: step six to eight, 70 degree sweep, 12 in out from the corner
• Home office: step two, fixed, aimed at the desk from three feet away

What Arrives and What It Weighs

Stand the tower upright for an hour after unpacking so the impeller settles on its mounts before the first run. The loop and the base ship as one piece; only the base plate needs the four screws in the carton.

Two Finishes

Silver pairs a white body with a brushed silver loop; Gold pairs the same white body with a champagne gold loop. Both use the same painted ABS, and both ship with a white remote. The loop is the one part that carries the finish, so the tower reads as white from across a room in either version.

The finish is paint over ABS, not anodised metal, so a scouring pad will dull it and a solvent will take it off. A damp cloth with a drop of dish soap is enough. The inner channel of the loop collects dust faster than the outside because that is where the air leaves, and it is also the part people forget.

Cleaning, Dust and Off-Season Storage

Wipe the loop's inner channel every two weeks in season. A dry microfiber cloth on a stick reaches the full height; the channel is where the air leaves, so it is also where the dust line forms.

Vacuum the lower intake grille with a brush head on the same schedule. A clogged intake is the usual reason a bladeless tower feels weak in its second summer, and it is also the usual reason the motor runs hotter than it should.

Do not spray cleaner into the slot. The slot leads directly into the impeller housing, and liquid that goes in will sit there. Spray the cloth, not the tower.

Before storage, run the tower on step ten for ten minutes with the room windows open to dry the impeller housing, then wipe the loop and coil the cord loosely.

Store upright if you can, or on its side with the loop supported. Storing it face down puts the whole weight of the base on the loop seam.

There is no user-serviceable bearing. If the tower develops a scrape or a squeal at low speed, stop using it: that is the impeller touching the housing, and running it will damage the motor.

Specifications

Frequently Asked Questions

Shipping, Returns and Warranty

Every HKM-016787 ships with the store policies below. Returns and warranty requests follow the same coverage window shown in the four panels, and support answers within one business day.

The HKM-016787 is a 39 in bladeless tower for the room where a bladed fan does not belong: a nursery, a bedroom with a toddler, a living room with a cat that climbs. Ten speeds, 70 degrees of sweep, a 1 to 8 hour timer, a remote that lives on the tower, and a loop you can wipe in under a minute. It moves air rather than chilling it, so it will not rescue a 95 F afternoon, but it will make a still room sleepable and it will do it without a blade at knee height.