HKM-6776787 Large Capacity 47oz Double Wall Insulated Stainless Steel Vacuum Coffee and Tea Pot

HKM-6776787 · Electric Kettles · 47 oz, Double Wall, Blue or Red

Slim Column, Lever Lid, Powder Coat

HKM-6776787 is a tall vacuum carafe — 47 oz / 1380 ml — built as a narrow column: 274 mm high, 105 mm across the base and 139 mm to the outside of the handle, with a powder-coated shell, a flush lid and a pouring lever set into the lid rim. The shell colours sold here are blue and red, with black and a full custom programme shown in the supplier's graphics.

It suits a table where space is tight and the pot stays put: the footprint is barely wider than a mug, the handle is a flat strap that hugs the body, and the lid sits flush so the whole object reads as a single column. The 47 oz fill pours six small cups or four large ones.

At a Glance

• Type — vacuum carafe with a lever lid, non-electric
• Capacity — 47 oz (1380 ml), per the size graphic
• Dimensions — 274 mm high, 105 mm base, 139 mm with handle
• Body — double wall, vacuum sealed, powder-coated shell
• Lid — flush disc with a pouring lever at the rim
• Colours — blue or red as sold; custom logo and CMF available

Materials and Construction

The body is a straight cylinder with a slight shoulder at the top, where the shell turns in to meet the lid. Inside, the liner is a second wall with the air evacuated between them, which is what holds temperature without the outside becoming hot or wet. The outer shell carries a powder coat with a fine texture, visible in the close views as a surface that scatters light rather than reflecting it.

The handle is a flat strap in the body colour, mounted high at the shoulder and low at the waist, standing off the shell on two short brackets. The lid is a flush disc with a small lip at the front and a lever along its rim; the lever is the pour control, worked by the thumb of the hand holding the handle.

• The base is flat and slightly recessed, which is what keeps a tall column stable on a tray.
• The spout is a short beak cut into the shoulder, level with the lid rather than above it.
• The lid sits inside the rim rather than over it, so the silhouette stays unbroken.

How It Works

Fill through the open neck with the lid off, seat the lid, and press the lever to pour. The lever works a valve inside the lid, so the carafe can be carried and tipped without opening it, and the pour stops when the lever is released. Because the valve is in the lid rather than in the spout, the stream starts as soon as the lever moves rather than after the body is tilted far enough to reach the lip.

The vacuum gap does the holding. No hour figure is published for this model, so none is claimed; what the construction promises is that the outside stays at room temperature while the inside holds hot liquid, and that the shell does not sweat when the contents are cold.

Two volumes appear in the supplier's material: the size graphic prints 47 oz / 1380 ml, and the retail box prints 2.0 L / 68 oz. The size graphic is the one drawn around this body's dimensions, so 47 oz is the figure used here, with the box figure recorded as printed rather than reconciled.

Placement and Use

It lives on a table, a tray or a desk, and the narrow footprint is the point: 105 mm of base for a 47 oz body. Keep the spout turned toward the room and the lever side facing the hand that pours, and leave height above the lid for lifting it off at the refill.

• Fill below the neck; the lid seals on the rim, not on the thread alone.
• Press the lever fully rather than part-way, so the valve opens cleanly.
• Set it down on a dry surface — the shell does not sweat, but a wet base will mark wood.

Included and Optional

Colours and Finishes

Blue and red are the two colours sold, at the same price. The blue is a deep teal-leaning shade and the red a dark brick tone; both are powder-coated with the same fine texture, and both carry a lid and handle in the body colour.

The supplier's graphics go further: a size sheet shows a black version alongside the two colours, and a finishing sheet sets out water-transfer printing for a checkered shell, diamond painting for a metallic sparkle, gradient painting for a two-tone fade, plus UV coating, mask PVD, paint transfer, 3D painting and a water system. Those are custom-programme options rather than stock colours, and the listing carries custom logo, custom CMF and sample variants to match.

Care and Maintenance

Rinse the liner with warm water after use and leave the lid off to dry, so the valve and the seal are not kept wet. Tea and coffee tannin lift with a warm soak and a little bicarbonate; a soft bottle brush reaches the floor of a narrow column without scratching it. Strong chlorine and aggressive descalers are not for stainless.

The powder coat wipes with a damp cloth. The carafe should not be immersed — the vacuum seam at the base is sealed rather than welded shut — and neither body nor lid is dishwasher safe. Store it with the lid loose so air moves through the liner between uses.

Specifications

Frequently Asked Questions

Shipping, Returns and Warranty

Every HKM-6776787 is backed by coverage designed to protect your investment.

HKM-6776787 · 47 oz vacuum carafe · 274 mm column · lever lid · blue or red powder coat